Connection chip and technical characteristics in video transmission technology

1. The video format is related to the clarity and authenticity of the signal

As we all know, the video transmission technology is very concerned about the clarity and authenticity of the video signal, as shown in Figure 1 for the common component video signal. Whether this can be done is inseparable from video signal filters, drivers, and multiplex switches and cable transmission devices. There are multiple input / output coupling and clamping combinations, including input AC or DC coupling, output AC or DC coupling and various combinations of input clamps are the connection chips and technologies in the video transmission technology. It should be said that it is a video format. For this reason, the technical characteristics will be discussed and introduced.

2. The input technology of the interface in the video transmission technology

2.1 AC coupled video input method

When designing analog video circuits, analog video signals are generally input through AC coupling (as shown in Figure 2). This allows the receiving circuit to establish the optimal DC bias level, and the capacitor isolates the DC voltage of the drive signal on this side of the output device. The classic way of recovering DC in AC-coupled video signals is achieved by separating the entire synchronization part embedded in the video signal and establishing a digital pulse signal.

2.2 DC-coupled video input method (as shown in Figure 3 (a))

In order to adapt to those single-end input drivers whose reference voltage is ground level and DC coupling, as shown in Figure 3, filter / drive devices such as FMS641 7A, FMS6418B and FMS6419 are specially designed for DC input coupling. For example, the standard current mode output of the video / graphic display DAC. In order to make the current-excited general-purpose DAC produce an output voltage, this DAC circuit often uses a double-terminated 75Ω (AC impedance equivalent to 37.5Ω) resistor as the load. Therefore, this type of DAC output has a known ground-referenced DC level. Devices with this type of DAC circuit can be seamlessly connected to the video DAC output, and have the following advantages: no input coupling capacitor is required; there is no clamping settling time; there is no signal amplitude reduction due to input capacitor discharge; no generation Glitch pulse; there is no limitation of input impedance when using pulsed DC recovery loop; there is no need for on-chip synchronous separation, charge pump circuit and servo loop.

2.3 About input-level design in TV design

Figure 3 (b) shows an input stage circuit of a modern TV. The video signal is AC coupled to the DC recovery circuit, so the input video signal can have any DC offset. The input circuit is compatible with AC coupled and DC coupled video signal sources.

However, it should be pointed out that there has never been a universally adopted solution in the design of input stage in TV design. In the past, a large number of televisions used different input stages. Whether the signal came from an AC or DC coupled signal source, it may cause problems for some televisions. For so many different types of receiving equipment, to achieve universal compatibility is Impossible. Based on cost considerations, the low-end video signal source, which accounts for the vast majority of signal transmission equipment, uses DC-coupled output.

3. The output technology of the interface in the video transmission technology

3.1 AC coupled output and DC coupled output

Whether to AC-couple the output depends mainly on technical and cost factors. The AC-coupled output circuit includes a series capacitor (Figure 4a), while the DC-coupled output circuit does not have this capacitor (Figure 4b). Adding a capacitor to the output channel will cause cost Improvements, increased space, and video signal distortion will cause the output waveform to "tilt" upward or downward relative to the input waveform. Therefore, this field distortion is called "field tilt". The DC-coupled output has no field tilt, so designers of video output circuits must take it seriously.

Since AC coupling has shortcomings, why is it still in use? There are two reasons. First, in order to play a protective role, the integrated circuit has not yet used a simple NPN emitter follower to drive the video output circuit before it is widely used. In case the output connector is shorted to ground or the power supply voltage, the capacitor prevents the NPN transistor from being damaged. The current integrated video amplifier has a solid short-circuit protection circuit, so it will not be damaged when a short circuit occurs. Second, starting from the technical characteristics, the most common method of outputting the video signal to the media display device is AC coupling (as shown in Figure 4 (c)), which allows the receiving circuit to establish a common mode level at its own input, This level is independent of the DC level of the input video signal. A 75Ω series resistor should be placed as close to the output as possible, which helps isolate the downstream parasitic interference generated from the output and provides the best signal conditions. The MAX4090 in Figure 4 (c) is the filter driver.

For AC coupling, one of the issues that should be paid attention to is that the coupling capacitance is usually relatively large, that is, 220 μF or greater. This is because the pole frequency formed by the capacitor and the 150Ω load (the sum of the reverse termination resistance and the input termination resistance) should be much lower than the frame frequency (25Hz or 30Hz). A 220μF capacitor forms a pole frequency of 5Hz, which is difficult to meet the performance requirements. Broadcasting equipment usually uses coupling capacitors of 470μF or 1000μF. Figure 4 (d) shows the high-pass response characteristics of AC-coupled output when using 220μF and 22μF capacitors. The minimum capacity of the AC coupling capacitor should be 200μF, which is the smallest coupling capacitor that can be used to obtain acceptable signal distortion.

OEM Original iPhone Battery Pack are brandnew cell with 0 cycle,protection board and FPC is same as original 1:1.We offered iPhone battery replacement made by 100% pure Lithium cobalt oxide which is AAA high quality,more durable rather than ternary material.AOKAL have professional experiences on iPhone Replace Battery for 5 years,we are totally understand which kind of Apple Battery Replacement is more stable and safety.We are professional manufacturer on iPhone battery only!

iPhone Battery Specification:

Item No.	Capacity(mAh)	(Whr)	Nominal Voltage(V)	Limited Charge Voltage(V)	Cell Size(mm)
iPhone 4	1420	5.20	3.7	4.2	423482
iPhone 4S	1430	5.30	3.7	4.2	423482
iPhone 5	1440	5.45	3.8	4.3	363292
iPhone 5S	1560	5.92	3.8	4.3	363491
iPhone 5C	1510	5.73	3.8	4.3	363391
iPhone SE	1624	6.21	3.82	4.35	363390
iPhone 6	1810	6.91	3.82	4.35	333996
iPhone 6Plus	2915	11.10	3.82	4.35	3348119
iPhone 6S	1715	6.55	3.82	4.35	293996
iPhone 6S Plus	2750	10.45	3.8	4.35	2949119
iPhone 7	1960	7.45	3.8	4.35	333993
iPhone 7Plus	2900	11.10	3.82	4.35	3249119
iPhone 8	1821	6.96	3.82	4.35
iPhone 8Plus	2675

Certified Batteries

• 100% brand new, high quality
• ORIGINAL OEM BATTERY (Original Equipement Manufacturer)
• Recharge Cycle :500-800 times
• Raw materials:

      Negative electrode: Graphite

• Integrated Dual IC chip protection
• Anti-overload, for a longer life
• Anti-short circuit, to protect your data
• Working  temperature: 0-30℃
• Battery certified to manufacturer's standards RoHS, CE, FCC, ISO9001
• These batteries have exactly the same size as the original batteries
• Warranty: 12 months

Batteries complying with conformity certificates.

• 
• RoHS : Restriction of the use of certains hazardous substances in electrical and electronic equipment.
  This standard is intended to limit the use of 6 hazardous substances.

• 
• CE : European Conformity, Batteries meeting European technical harmonization standards. The batteries were subjected to design and control checks; And meeting the essential technical requirements established by the European Directive.
  This marking allows free movement within the European market.

• 
• Certificate of the quality management system.
  ISO 9001 is an international standard, which defines the requirements of a quality management system to increase customer satisfaction and improve the functioning of the company.

Welcome OEM/ODM order,accepted small order start from 100pcs. If you have any questions, please do not hesitate contact with us.iPhone battery are produced by 

iPhone Battery

iPhone Battery Pack,Internal iPhone Battery Pack,iPhone Battery 0 cycle,iPhone battery replacement,iPhone battery original capacity

Shenzhen Aokal Technology Co., Ltd. , https://www.aokal.com