Keywords: electric cylinder/servo electric cylinder/electric cylinder/servo electric cylinder/electric actuator/servo electric actuator/servo actuator/electric slide/linear module/linear module/robot/servo motorized slide/servo Sliding table
Shanghai Guangjian Automation Equipment Co., Ltd. is located in Shanghai National Automobile Anting High-tech Development Zone. It is a professional R&D, design, production and sales of servo electric cylinders, multi-freedom platforms, linear modules, robots, control systems, and transmission systems. The innovative high-tech enterprise. Through years of hard work and the use of advanced modular concepts from abroad, GJ20 series servo electric cylinders and GJ80 series linear modules have been successfully developed. The series products have the characteristics of compact structure, low inertia, high response, low friction, low noise and low speed and stability. Leading the same products. To provide customers with simple, efficient, stable performance of national industrial products.
First, the characteristics of servo electric cylinder:
Fast acceleration, short positioning time, good dynamic performance (fine, accurate, fast, steady)
* Precise, strong
* Can be used uniaxially
*Can be used for multi-axis combination
* Modular application
* Simple structure saves mechanical design space
* With a variety of installation and connection methods and accessories available for design choice
*Can be used with a variety of motor and motor control regulators
* Multi-point positioning and multi-segment control
* Use appropriate accessories to increase assembly efficiency
* Satisfy different design accuracy requirements
* Save time, easy maintenance
* Clean room rating: ISO Class 5 to 6 (100 to 1000)
* Provide two types of ball screw type and synchronous tooth type belt type for customers to choose design
* Products are diversified, easy to use, and can be tailor-made for special customized products.
* Drive method can be selected according to the use of ball screw drive or belt drive.
* The motor connection can be selected according to the use of space, built-in motor, direct motor, motor indirect, motor down or up, motor left or right.
Second, the main technical parameters of servo electric cylinder:
Specifications Transmission Repeat Positioning Accuracy (mm): +/-0.01,+/-0.02,+/-0.05
Screw diameter (mm): 30,35,40,45,50,60,70,80,100
Screw lead (mm): 4,5,10,20,40
The fastest speed mm/s: 20,50,80,100,150,200,500,1000,2000
Maximum load rated thrust (N): 50,100,200,500,1k-35k
Effective stroke (mm) 50,80,100,150,200,250,300,350,400,500-2000
Horizontal use (kg): 10,50,100,200,300,400,500-3500
Vertical use (kg): 10,50,100,200,300,400,500-3500
Third, the use of matters needing attention:
1. The servo electric cylinder is a precision electromechanical product. Please read the precautions for use and the instructions for use of the relevant motor and driver in advance when using it. Pay attention to it during use. Do not disassemble the electric cylinder without the permission of the manufacturer. Is the screw outside the electric cylinder, otherwise the manufacturer will not be responsible.
2. The servo electric cylinder is a basic maintenance-free product, and any exchange of parts and components must be carried out at the authorized place of the manufacturer or the manufacturer. Otherwise, the manufacturer will not be responsible.
3, The motor and servo electric cylinder are connected by high-strength timing belt and adjusted by tension. So do not disassemble the motor at will, otherwise it will cause the timing belt to be damaged due to improper tension.
4. Never apply more than 10.8Nm external force on the piston rod during installation to avoid damage to the electric cylinder.
5,The servo electric cylinder adopts the grease lubrication method. There is a grease adding port on the cylinder body. When adding, use the Mobilith SHC220 grease and grease gun. The adding amount and period are: 2 times (gun stroke)/6 months ( Or 50 km journey)
The method of refueling the screw nut is: After the full stroke of the electric cylinder is extended, the motor is stopped and the power is cut off. The screw plug at the injection hole of the screw oil on the cylinder barrel is opened, and the fuel plug is used for refueling. After refueling, Install the screw plug, turn on the power, and walk 2 to 3 times for the whole journey.
7. When commissioning the servo electric cylinder, it should be done at low speed first, and then increase the speed after everything is normal to avoid damage to the electric cylinder.
8. It is forbidden to touch the sliding seat and maintain the safe working range during product work.
9. When the ball screw product is used vertically [Z axis] It is recommended that the motor be equipped with a brake device to prevent the object from dropping. The gear belt drive is not recommended for vertical use [Z axis].
10. Resonance may occur when the effective stroke is too large, and the maximum speed should be relatively reduced when the stroke is greater.
Fourth, servo electric cylinder lubrication:
1) Lubrication is very necessary when servo electric cylinders are used. If there is not enough lubrication, the frictional resistance will increase during operation and may become the main reason to shorten the product life. Lubrication methods are roughly divided into manual lubrication and automatic forced lubrication. Depending on the operating speed of the system, the use of the environment and other needs to make appropriate choices
2) The frequency of lubrication is different depending on the conditions of use and the environment. In general, it is recommended to refill the oil once every 100km.
Fifth, servo electric cylinder maintenance:
Standard type
1. When the standard servo electric cylinder is used for maintenance and oiling, the top cover must be removed and the buttered mouth must be connected to inject proper grease.
2. The standard type servo electric cylinder is often subject to uneven lubrication due to internal space constraints.
3. When the built-in oil system specification is maintained, grease can be directly injected into the grease fittings on both sides of the sliding seat, and no components need to be disassembled and the manpower and material resources required for maintenance can be saved.
4. The built-in oil circuit system ensures even lubrication of the slides and screws during oil filling and maintenance, effectively achieving the function of parts maintenance.
5. The oil circuit system is optional. If you have other questions, please contact us. We will do the relevant service and explain you as soon as possible.
Six, servo electric cylinder use range:
Workpiece positioning\carrying\clamping\inserting capacity automation equipment, reciprocating sprayer, printing equipment, mechanical arm, packaging machine equipment, chemical equipment, food equipment, metal processing equipment, textile machinery, woodworking equipment, transfer equipment, automatic Dispensing equipment, automatic processing equipment, workpiece positioning equipment, labeling machine, laser cutting and positioning, water cutting and positioning, ultrasonic welding positioning, medical equipment, solar energy equipment, etc.
Seven, servo electric cylinder sales instructions and recommendations:
2 This product is guaranteed for one year from the date of shipment from the factory, under normal use conditions (ie non-human damage).
2 If the damage is caused by human factors or other abnormal use, it will not be covered by the warranty.
2 This product is forbidden to disassemble after leaving the factory. Once disassembled, it will not be responsible for the warranty.
2 It is recommended that customers should add lubricant to each electric travel distance of 100 km.